For homes
We run gas lines for ranges, dryers, water heaters and fireplaces in houses, condos and townhomes. We check the load and test the line before we leave.
- New range or dryer line
- Gas leak near water heater
- Old pipe replacement
Gas line services Arlington Heights IL done right the first time
When you need gas line services Arlington Heights IL homeowners can count on, we run new gas pipe installation Arlington Heights properties require and repair leaks before they become emergencies. From a new stove hookup at 60004 to a full line replacement in Scarsdale, our crew handles permits, pressure testing and code compliance. We work on copper, PEX and black steel, and we test every connection before we leave.
Leak checkPressure testPermit pulled- We test firstGauge holds before we leave
- We pull permitsInspection handled on site
- We protect floorsDrop cloths and vacuum
- We explain findingsPlain English, no jargon
What our gas line service includes
Every gas line job starts with a full inspection and ends with a pressure test. The scope depends on whether you need a new run, a repair or a replacement, but the core steps are the same. Here is what is covered and what we handle as an add-on.
Full gas line inspection
We check the meter, the appliance connection and every visible joint between them. We look for corrosion, kinks, undersized pipe and missing shut-off valves. If the run is behind a wall, we use a combustible gas detector to check for leaks at the openings. You get a plain-English report of what we found.
Permit and inspection coordination
For new installations and replacements, we pull the Arlington Heights permit and schedule the Cook County inspection. We meet the inspector on site and correct anything they flag. You do not have to call the village or take a day off work to let the inspector in.
Pipe installation or repair
We install copper pipe, black steel or PEX tubing depending on the appliance load and the route. Repairs involve cutting out the failed section, fitting a new piece and soldering or crimping it in place. We use a pipe cutter and a soldering torch or PEX crimping tool, and we keep the work area clean.
Pressure test and leak check
After the work is done, we pressurize the line to 10 PSI and hold it for 15 minutes. If the gauge moves, we find the leak and redo the joint. We also check each connection with leak detection equipment. You watch the gauge hold before we leave.
Appliance connection and startup
We connect the appliance, install a shut-off valve at the connection point, and relight the pilot if needed. We check the flame color and height and confirm the appliance runs correctly. If it does not, we troubleshoot the appliance side before we call the job done.
Cleanup and walkthrough
We lay drop cloths, vacuum metal shavings and wipe down surfaces. Then we walk you through what we did, where the shut-off valve is, and what to watch for over the next week. You get a photo of the valve location and the pressure-test record.
Homes and businesses.
The approach is the same for a home and a business. What changes is the access, the schedule and who needs the paperwork.
For businesses
We run gas lines for restaurants, laundromats and shops in commercial buildings. We calculate the load, pull the permit and schedule the inspection around your hours.
- Kitchen equipment hookups
- Commercial water heaters
- After-hours gas repairs
Gas line services Arlington Heights IL explained
A plain-language look at what Gas Line Services involves and when it is needed.
See how it worksThat covers a new gas pipe installation Arlington Heights homeowners need for a range, dryer or outdoor grill, a gas line repair Arlington Heights, Illinois properties require after a leak, and full replacement of corroded or undersized piping. We pressure-test every run with a gauge, check each joint with leak detection equipment, and confirm the appliance fires correctly before we sign off.
Most calls we get in Arlington Heights start the same way: a homeowner smells gas near the water heater, a new range sits in the kitchen with no line behind it, or a 1950s ranch off Miner Street Corridor still has the original black steel pipe feeding a furnace. Cook County winters push furnaces hard from November through March, and that demand exposes weak joints and undersized runs. If you are searching for gas line services near me Arlington Heights IL, we can usually be on site the same day.
A gas line is only as good as its pressure test and its permit.
- When you need it
- When you smell gas, add a gas appliance, or replace corroded or undersized pipe.
- What to expect
- An inspection, a flat quote, the work, a pressure test and a walkthrough.
How our gas line service works
From the first phone call to the final pressure test, here is exactly what happens when you book gas line services Arlington Heights IL with our crew. No mystery, no waiting around for a callback that never comes.
-
Phone triage
You call (224) 643-9856 and describe what you smell, see or need installed. If it is an active leak, we tell you to leave the house and call the gas utility first, then we dispatch. For non-emergency work, we book a two-hour arrival window, usually same-day or next morning. You get a text when the tech is en route.
- Call
- Describe
- Book
-
On-site inspection
The tech walks the meter, the appliance and the run between them. We check for corrosion, kinks, undersized pipe and missing shut-off valves. On a replacement, we camera the wall cavity if accessible. This takes 20 to 30 minutes and ends with a plain-English explanation of what we found and what it takes to fix it.
- Inspect
- Measure
- Explain
-
Permit and plan
For new installations and replacements, we pull the Arlington Heights permit and schedule the Cook County inspection. You get a written scope the same day: pipe material, route, appliance load, shut-off locations and the inspection window. No work starts until you approve it.
- Permit
- Scope
- Approve
-
Install or repair
Most repairs finish in two to four hours. A full replacement or new run takes four to eight hours depending on length and wall access. We cut, fit, solder or crimp, then pressurize the line to 10 PSI and hold it for 15 minutes. If the gauge moves, we find the leak and redo the joint before moving on.
- Cut
- Fit
- Test
-
Test and handoff
We relight pilots, confirm the appliance fires, and check the flame color and height. You get a pressure-test record, a photo of the shut-off valve location, and a walkthrough. If the inspector is scheduled, we meet them on site.
- Relight
- Check
- Walkthrough
Tools and methods we use on gas lines
Move across a circle, or focus it and press Enter, for an illustrative thermal view of the photograph.
Combustible gas detector
Handheld detector that sniffs for gas at joints, valves and appliance connections. We use it to confirm a leak before we open a wall and to verify the repair after we finish.
Pressure gauge
We pressurize the line to 10 PSI and hold it for 15 minutes. The gauge tells us whether the run is tight. If it moves, we know there is a leak and we find it before we leave.
Pipe cutter and tube cutter
Clean, square cuts on copper pipe and black steel. A square cut means a better solder joint or crimp, which means fewer leaks down the road. We do not use a saw where a cutter will do.
Soldering torch and PEX crimping tool
We solder copper joints and crimp PEX connections. Both methods are code-approved when done correctly. The choice depends on the route, the wall access and the appliance load.
Leak detection equipment
Beyond the gas detector, we use soap solution and pressure-drop testing to confirm every joint. We check each connection individually, not just the line as a whole.
Thermal views are illustrative, generated from the photographs.
Methods
RIDGID and Milwaukee hand tools
Pipe wrenches, tubing cutters and cordless tools from RIDGID and Milwaukee. We keep them on the truck so we are not making a supply run in the middle of your job.
Pressure testing to 10 PSI
We isolate the new or repaired section, pressurize it to 10 PSI and hold for 15 minutes. The gauge must not move. This is the same standard the inspector uses, so we know the line will pass before we call for inspection.
Load calculation before sizing
Every appliance has a BTU rating. We add up the load and size the pipe so the appliance gets steady pressure at the connection. Undersized pipe is one of the most common problems we find on older Arlington Heights homes.
Leak check at every joint
After the pressure test, we check each joint with a combustible gas detector and soap solution. We do not rely on a single test at the meter. If one joint fails, we redo it and re-test the whole run.
Permit and inspection coordination
We pull the Arlington Heights permit, schedule the Cook County inspection and meet the inspector on site. If they flag something, we correct it and re-test. You do not have to manage the paperwork.
Appliance startup and flame check
We relight pilots, confirm the appliance fires and check the flame color and height. A blue flame with a steady height means the gas pressure is correct. A yellow or lazy flame means we need to adjust the air mixture or check the line size.
When Arlington Heights homeowners call us
New range line
You bought a new gas range and need a line run from the basement to the kitchen.
We run copper pipe or PEX tubing from the nearest existing gas run to the range location, install a shut-off valve and connect the appliance. We pull the permit and pressure-test the line. The work usually takes four to six hours.
Outcome: You cook on gas the same day. The line passes inspection and the shut-off valve is accessible behind the range.
Gas smell
You smell gas near the water heater on a cold January morning.
We dispatch a tech with a combustible gas detector and pressure gauge. We isolate the leak, repair the failed joint or section, and re-test the entire run. If the water heater itself is the source, we repair or replace the gas valve or thermocouple.
Outcome: The leak is sealed, the line holds pressure and the water heater fires clean. You get a written pressure-test record.
Old pipe swap
Your 1960s ranch in Pioneer Park still has the original black steel gas pipe feeding the furnace and water heater.
We replace the run with correctly sized copper pipe or PEX tubing, upsize if the load requires it, and install new shut-off valves at each appliance. We pull the permit and meet the inspector.
Outcome: Both appliances get steady gas pressure, the flames burn blue and the system passes inspection. You avoid a mid-winter failure.
Fireplace line
You are adding a gas fireplace or a pool heater and need a new line run.
We calculate the BTU load, choose the pipe size and material, and run the line from the meter to the appliance. We install a shut-off valve and pressure-test the run. Outdoor runs get pipe rated for exterior exposure.
Outcome: The fireplace or pool heater fires correctly and the line holds pressure. The permit and inspection are handled.
Kitchen remodel
You are remodeling the kitchen and want the gas line moved behind the new island.
We reroute the existing line, extend it to the new location and install a shut-off valve. We coordinate with your contractor on wall openings and timing so the drywall goes back once.
Outcome: The range sits where you want it, the line is code-correct and the inspection passes. No second round of demolition.
How gas line work runs in Arlington Heights
Arlington Heights has a mix of housing stock that affects gas line work. Downtown and Old Arlington Heights have older homes with original black steel pipe, often undersized for modern appliances. Scarsdale and Sherwood have 1960s and 1970s ranches where the gas line runs through the basement ceiling and is easy to access.
Newer construction near Arlington Market and Creekside often has PEX tubing already in place, which makes adding a line simpler. Cook County winters push furnaces and water heaters hard from November through March, and that is when we see the most gas line leak repair Arlington Heights IL calls. The ground freezes to 30 inches or more, so exterior runs need to be buried below the frost line.
If you need affordable gas pipe repair in Arlington Heights, Illinois, we can usually be on site the same day.
- Old Arlington Heights: Older homes with original black steel gas pipe. Many runs are undersized for modern tankless water heaters and need to be replaced or upsized.
- Scarsdale: 1960s ranches with basement gas runs. Access is usually easy, which keeps installation costs lower than homes with finished basements.
- Arlington Market: Newer construction with PEX tubing and modern shut-off valves. Adding a gas line for a grill or dryer is usually a short run from an existing manifold.
- Downtown Arlington Heights: Condos and mixed-use buildings where gas lines run through shared walls. We coordinate with building management on shut-offs and inspection access.
- Pioneer Park: Mid-century homes where the gas line often feeds both the furnace and water heater. We check the load before adding any new appliance.
- Frozen ground from December through March: Exterior gas line runs must be buried below the frost line, which is 30 inches or deeper in Cook County. We schedule exterior work before the ground freezes or wait for the spring thaw.
We walk the meter and appliance with you. We lay drop cloths and set up tools. We test the line and explain the results.
From problem to finished result.
Cracked fitting on a water heater line
Before: A homeowner in Scarsdale smelled gas near the water heater. The fitting at the tank connection had cracked from years of heat cycling. The line failed a pressure test and the water heater would not stay lit.
After: We replaced the cracked fitting, added a new shut-off valve and pressure-tested the run to 10 PSI for 15 minutes. The gauge held. The water heater fired clean and the gas smell was gone. Total time on site: two hours.
Check the connection at the water heater once a year for corrosion or soot. If you smell gas, leave the house and call the utility before calling us.
New gas line for a kitchen range
Before: A homeowner in Downtown Arlington Heights bought a new gas range but the kitchen had no gas line. The nearest run was in the basement, 25 feet away through a finished ceiling. They were using a propane tank temporarily.
After: We ran 25 feet of copper pipe from the basement run to the range location, installed a shut-off valve and connected the appliance. The permit was pulled and the inspection passed on the first visit. Total time: six hours.
Keep the shut-off valve accessible behind the range. If you remodel the kitchen, call us before you close the wall so we can inspect the line.
Full replacement of undersized black steel
Before: A 1965 ranch in Pioneer Park had original black steel pipe feeding a furnace and water heater. The pipe was undersized for the new tankless water heater the homeowner wanted. The old line also had surface corrosion at two joints.
After: We replaced the run from the meter with correctly sized copper pipe, installed new shut-off valves at both appliances and pressure-tested the system. The tankless heater fired correctly and the furnace flame was steady blue. Total time: one day.
Have the gas line inspected every two to three years, especially if you add a new appliance. Keep the area around the meter clear of storage.
Gas line problems we fix in Arlington Heights
Gas problems do not fix themselves, and they do not get cheaper with time. Here are the calls we run most often and what happens if you let them sit.
- Gas smellGas smell near the water heater or furnaceA gas leak can cause a fire, an explosion or carbon monoxide poisoning. If you smell gas, leave the house and call the utility first. Do not flip switches or use your phone inside. We dispatch a tech with a combustible gas detector and pressure gauge. We isolate the leaking joint, repair or replace the section, and pressure-test the entire run. Most leak repairs finish in two to four hours. We do not leave until the gauge holds and the appliance fires clean.
- No appliance lineNew gas range or dryer with no line behind itYou cannot use the appliance, and running an extension cord or a propane tank is not a safe workaround. The longer the appliance sits, the more likely you are to pay a restocking fee or miss a return window. We run a new gas line from the meter or the nearest existing run to the appliance location. We size the pipe for the BTU load, install a shut-off valve and pull the permit. A standard run takes four to six hours and passes inspection the first time.
- Corroded pipeOld black steel pipe that is corroded or undersizedCorroded pipe leaks. Undersized pipe starves the appliance, causing weak flames, long ignition times and premature failure on water heaters and furnaces. Both problems get worse in cold weather when demand is highest. We replace the run with correctly sized copper pipe or PEX tubing, or upsize the black steel if the route requires it. We pressure-test the new line and confirm the appliance gets steady pressure.
- New stove hookupGas line for a new stove or outdoor grillWithout a dedicated line, you are stuck with a propane tank or an extension hose that is not rated for permanent use. That is a code violation and a safety risk, especially for a grill on a wood deck. We run a dedicated line to the appliance location, install a shut-off valve and test the connection. For outdoor grills, we use pipe rated for exterior use and protect the run from the weather. A gas line for new stove Arlington Heights 60004 installation usually takes three to five hours.
- Failed inspectionGas line that failed inspection during a home saleA failed gas inspection can delay or kill a real estate closing. The buyer's lender may hold funds until the line is corrected and re-inspected, which puts your timeline at risk. We inspect the line, correct the code violations, pull the permit if needed and meet the inspector on site. We provide the pressure-test record and the inspection sign-off so your closing stays on track. Most corrections take one day.
Why Arlington Heights homeowners call us
A code-correct gas line that passes inspection and holds pressure.
Code-correct from day one
We pull the permit, schedule the inspection and correct anything the inspector flags at no extra charge. That matters when you sell the house and the buyer's inspector asks for paperwork on the gas line for new stove Arlington Heights 60004 installation you had done three years ago.
Leak detection that finds it fast
We use leak detection equipment and a pressure gauge to isolate the exact joint or section that is failing, instead of tearing into walls hoping to find it. A typical gas line leak repair Arlington Heights IL call takes 90 minutes to two hours from arrival to a confirmed, sealed fix. You get a written pressure-test result before we pack up.
Right-sized pipe for the appliance
A dryer needs a different BTU capacity than a tankless water heater. We calculate load, then choose between copper pipe, PEX tubing or black steel so the appliance gets steady pressure. Undersized gas piping Arlington Heights homes often have causes weak flames, long ignition times and premature failure on Rheem and AO Smith units.
Clean work, no surprises
We lay drop cloths, cut with a pipe cutter instead of a saw where possible, and vacuum metal shavings before we leave. Shut-off valves go in at the appliance so you can isolate it without killing gas to the whole house. You get a walkthrough of what we did, what we tested and what to watch for over the next week.
What you receive
Clear records you can keep and share.
Pressure log
Gauge reading and hold time recorded
Valve photo
Picture of shut-off valve location
Scope sheet
Pipe size, route and materials listed
Inspection slip
Signed inspection record when required
Repair, replacement or new run
Most gas calls fall into three categories. Knowing which one you need helps you ask the right questions.
Repair
Fixing a failed joint or short section
- Leak at a fitting
- Cracked valve
- Corroded nipple
Replacement
Swapping the full run from the meter
- Undersized pipe
- Widespread corrosion
- Failed inspection
New run
Adding a line for a new appliance
- Range or cooktop
- Dryer or grill
- Fireplace or heater
Materials and parts we use
- Copper pipe
- Black steel
- PEX tubing
- Pipe fittings
- Shut-off valves
- Teflon tape
- Solder
- Pressure gauge
Service ZIP codes.
A list like this tells people straight away whether you cover their street. Not listed? Call and ask: it only takes a minute.
- 60005
- 60004
Towns we serve.
Based in Arlington Heights and covering the places around it. Pick one for local details.
- Downtown Arlington Heights
- Arlington Heights Business District
- Scarsdale
- Northgate
- Pioneer Park
- Greenbrier
- Creekside
- Lake Arlington
- Arlington Market
- Hasbrook
- Westgate
- Countryside
What Arlington Heights customers say
Frequently asked questions about gas line work
The price depends on run length, wall access, pipe material and whether a permit is required. A short run to a dryer in an open basement sits at the low end. A long run through finished walls to a kitchen island sits at the high end. We quote flat before we start.
Handymen and general contractors cannot pull the gas permit.
A typical replacement takes four to eight hours of on-site work, plus the inspection window. If the old line runs through finished walls, we may need a second day to open and patch. Most homeowners have gas back on the same day we start. We pressure-test at the end and relight every pilot before we leave.
Yes. Arlington Heights requires a permit for new gas lines, replacements and any work that alters the run from the meter. Minor repairs to an existing joint sometimes qualify as service work, but we pull the permit when the scope requires it. We handle the paperwork and the inspection so you are not chasing the village hall.
Other plumbing services we handle
Other services from the same team.
- Gas Leak Detection and RepairIf you smell gas, leave and call us. We use leak detection equipment to pinpoint the source, shut off the supply, and repair or replace the failed section. We pressure-test after the repair and confirm the line holds before restoring service.
- Pipe Repair and ReplacementFrozen pipes, pinhole leaks, and corroded galvanized lines cause most of the pipe repairs we see. We cut out the bad section, install copper pipe or PEX tubing, and pressure-test the repair. Burst pipe calls get priority dispatch.
- Repiping ServicesWhen pipes are corroded throughout, spot repairs just delay the next leak. We repipe homes with copper or PEX, usually in two to four days, and restore water the same day we finish. You get a cleaner, higher-pressure system.
Need gas line services Arlington Heights IL today?
We pull the permit, pressure-test the line and meet the inspector. Same-day service available across Arlington Heights and Cook County.
Contact Five Star Plumber LLC
Call (224) 643-9856 or email us and we will get back to you fast. Tell us what is going on and we will tell you what it takes to fix it.